Standard D-Subminiature (D-Sub) Connectors
|
Standard
D-Subminiature Connector Selection Chart |
||||||||
|
Series 'C' |
Series 'S' |
Series 'FR' |
Series 'HD' |
|||||
|
Crimp &
Poke Style |
Solder
Pot Style |
IDC Style |
|
|||||
|
9-Position |
9-Position |
9-Position |
15-Position |
|||||
|
Male |
Female |
Male |
Female |
Male |
Female |
Male |
Female |
|
|
|
|
|
|
|
|
|
|
|
|
100901WX |
100902WX |
1209101WXY |
120902WXY |
130901WXY |
130902WXY |
151501WXY |
151502WXY |
|
|
15-Position |
15-Position |
15-Position |
26-Position |
|||||
|
Male |
Female |
Male |
Female |
Male |
Female |
Male |
Female |
|
|
|
|
|
|
|
|
|
|
|
|
101501WX |
101502WX |
121501WXY |
121502WXY |
131501WXY |
131502WXY |
152601WXY |
152602WXY |
|
|
25-Position |
25-Position |
25-Position |
44-Position |
|||||
|
Male |
Female |
Male |
Female |
Male |
Female |
Male |
Female |
|
|
|
|
|
|
|
|
|
|
|
|
102501WX |
102502WX |
122501WXY |
122502WXY |
132501WXY |
132502WXY |
154401WXY |
154402WXY |
|
|
37-Position |
37-Position |
37-Position |
62-Position |
|||||
|
Male |
Female |
Male |
Female |
Male |
Female |
Male |
Female |
|
|
|
|
|
|
|
|
|
|
|
|
103701WX |
103702WX |
123701WXY |
123702WXY |
133701WXY |
133702WXY |
156201WXY |
156202WXY |
|
|
50-Position |
50-Position |
50-Position |
78-Position |
|||||
|
Male |
Female |
Male |
Female |
Male |
Female |
Male |
Female |
|
|
|
|
|
|
Check
Availability |
Check
Availability |
|
|
|
|
105001WX |
105002WX |
125001WXY |
125002WXY |
135001WXY |
135002WXY |
157801WXY |
157802WXY |
|
|
Series ‘RA’ |
9 ~ 50-Position |
|
||||||
|
Right Angle PCB |
Male |
Female |
||||||
|
Available by
Order Only |
|
|
||||||
|
Important Note:
Elite’s D-Subminiature connectors are subject to minimum
order requirements.
Product delivery trays will not be split.
Your order will be rounded up to the next reasonable
piece-part count to ensure trays are not split and your order
quantity is delivered in full. |
||||||||
|
|
14TT01WXY |
14TT02WXY |
||||||
|
Elite's
D-Subminiature Connectors meet or exceed accepted
electronics industry interface and packaging form-factors and
the specified mechanical, electrical and environmental
performance requirements and test criterion of ANSI/TIA/EIA 364
for electronic connectors; and, are RoHS Compliant. When
ordering D-Subminiature connectors, please ensure that you are
ordering the correct interface configuration for your
application. Elite Electronics specifies only the highest
quality raw materials for use in its D-Sub Plugs and
Receptacles. Elite Electronics requires its fabricating
sources to provide a written ISO Certificate of Compliance (C
of C) inclusive of the product's ISO Manufacturing Date
Code, RoHS - 2002/95/EC (Directive on the Restriction of the use
of Certain Hazardous Substances in Electrical & Electronic
Equipment) and WEEE - 2002/96/EC (Directive on Waste Electrical
& Electronic Equipment) with each production shipment. |
|||
|
|
|||
|
♦ |
Elite's Series
'C,' 'S,' 'FR,'
'HD' and
'RA' D-Subminiature Connectors
are fully compatible with all standard D-Subminiature connectors
with corresponding pin configurations. |
||
|
|
|||
|
♦ |
Two-piece glass-filled
engineered thermoplastic insulator system that meets or exceeds
the self-extinguishing requirements of UL 94 V-0. |
||
|
|
|||
|
♦ |
Available
Interface Pin Configurations: |
||
|
|
|||
|
|
● |
Standard Pin
Configurations: |
9, 15, 25, 37 & 50-positions |
|
|
|
|
|
|
|
● |
High Density Pin
Configurations: |
15, 26, 44,
62 & 78-positions |
|
Performance
Characteristics. Elite Electronics' D-Subminiature
Connectors will meet or exceed the performance characteristics
as specified in the most current version of ANSI/TIA/EIA 364.
Minimum electrical and environmental performance capabilities
shall be as follows: |
||
|
|
||
|
D-Subminiature Connector
Mechanical Features: |
||
|
|
||
|
A. |
Insulator: |
UL 94V-0 Glass Filled
Engineered Thermoplastic. |
|
|
||
|
B. |
Contacts: |
Stamped & Formed Brass or Phosphor Bronze. |
|
|
||
|
C. |
Shell: |
Stamped & Formed Steel. |
|
|
||
|
D. |
Plating: |
|
|
|
1. |
Contacts: |
|
|
|
|||
|
|
|
a. |
Nickel 50-microinches
(1.27 µm) as
under-plating. |
|
|
|||
|
|
|
b. |
Gold Flash <10-microinches
(<0.254 µm) |
|
|
|||
|
|
|
c. |
Selective Gold over the
nickel plated contact area, NC100 (or equivalent lead-free
solder) tinning over the nickel plated tail areas. |
|
|
|||
|
|
2. |
Shell
Housing: |
|
|
|
|||
|
|
|
a. |
Sulfamate Nickel (or
equivalent) over the copper plated stamped and formed metal
substrate; or, |
|
|
|||
|
|
|
b. |
Zinc Plated with yellow
chromate coating over the copper plated stamped and formed metal
substrate. |
|
D-Subminiature Connector Electrical Features: |
||
|
|
||
|
A. |
Current
Rating: |
5A |
|
|
|
|
|
B. |
Contact
Resistance: |
<30 mΩ
|
|
|
|
|
|
C. |
Insulation Resistance: |
5,000 mΩ |
|
|
|
|
|
D. |
Dielectric Voltage: |
1000 VAC RMS 50 Hz for minute at sea level |
|
|
|
|
|
E. |
Operating Temperature: |
-25°C ~ +55°C |
|
Performance Characteristic |
Test Procedure & Performance
Requirements |
|
Insulation Resistance |
ANSI/TIA/EIA 364 - 21: Test units must meet or exceed
a minimum of 5,000 MW. |
|
Dielectric Withstanding Voltage |
ANSI/TIA/EIA 364 - 20: The dielectric must withstand
1000 VAC RMS 50 Hz for minute at sea level. |
|
Low
Level Contact Resistance |
ANSI/TIA/EIA 364 - 23: 30 mW
maximum when measured at 20 mV maximum open circuit at
100 mA; Mated test contacts must be in a connector housing.
|
|
Contact Current Rating |
ANSI/TIA/EIA 364–70: 5A at 250 VAC minimum when
measured at +25°C;
With power applied to the contacts, DT shall not exceed +30oC at
any point in the D-Subminiature connector under test. |
|
Contact
Capacitance |
ANSI/TIA/EIA 364–30: 2 pF maximum per unmated contact.
|
|
Insertion Force |
ANSI/TIA/EIA 364–13: 35 Newtons maximum at a maximum
rate of 12.5 mm (0.492”) per minute. |
|
Extraction Force |
ANSI/TIA/EIA 364–13:
10 Newtons minimum at a maximum
rate of 12.5 mm (0.492”) per minute. |
|
Durability |
ANSI/TIA/EIA 364–09: 200 'insertion/extraction' cycles
at a maximum rate of 200 cycles per hour. |
|
Accelerated Life Testing |
ANSI/TIA/EIA 364–17: 250 Hours at +85°C with a 375 VPP 16 MHz square wave applied to
mated contacts. (Note: Mated contacts must be contained in an
Elite connector body.) |
|
Humidity Life Testing |
ANSI/TIA/EIA 364–31: 168 Hours, seven (7) complete
cycles. |
|
Random
Vibration |
ANSI/TIA/EIA 364–28: ms or longer duration1No discontinuities of when mated D-Subminiature
connectors are subjected to 5.35 Gs RMS. 15 minutes in each of
three mutually perpendicular planes. |
|
Physical Shock |
ANSI/TIA/EIA 364–27: No discontinuities of 1 ms or
longer duration when mated D-Subminiature connectors are
subjected to 11 ms duration 30Gs half-sine shock pulses.
Three shocks in each direction applied along three mutually
perpendicular planes for 18 shocks. |
|
Thermal
Shock |
ANSI/TIA/EIA 364–62: 10-Cycles ~
–25°C
and +85°C. The D-Subminiature connectors under test must be
mated. |
|
Solderability |
ANSI/TIA/EIA 364–52: D-Subminiature connector's contact
solder tails shall pass 95% coverage after one-hour steam aging
as specified in Category 2. |
|
Flammability |
UL
94-V0: Upon request D-Subminiature connector's
manufacturers are required to provide a C of C that shows the
insulator material’s UL listing number and/or test data that
shows the insulator material meets or exceeds the UL 94 V-0
Flame Impingement Test Criteria. |
|
EL SS TT UU WW X Y |
= |
Part Number Legend |
||
|
EL |
= |
Elite Electronics |
||
|
SS |
= |
D-Subminiature (D-Sub) Connector Series |
||
|
|
|
10 |
= |
Series ‘C’ ~ Crimp & Poke Style |
|
|
|
12 |
= |
Series ‘S’ ~ Solder Pot Style |
|
|
|
13 |
= |
Series ‘FR’ ~ IDC Style |
|
|
|
14 |
= |
Series ‘RA’ ~ Right Angle PCB Style |
|
|
|
15 |
= |
Series ‘HD’ ~ High Density Solder Pot Style |
|
TT |
= |
Connector Interface (Pin-Out) |
||
|
|
|
09 |
= |
9-Pin Positions |
|
|
|
15 |
= |
15-Pin Positions (Standard & High Density) |
|
|
|
25 |
= |
25-Pin Positions |
|
|
|
26 |
= |
26-Pin Positions (High Density) |
|
|
|
37 |
= |
37-Pin Positions |
|
|
|
44 |
= |
44-Pin Positions (High Density) |
|
|
|
50 |
= |
50-Pin Positions |
|
|
|
62 |
= |
62-Pin Positions (High Density) |
|
|
|
78 |
= |
78-Pin Positions (High Density) |
|
UU |
= |
Connector Interface Configuration |
||
|
|
|
01 |
= |
Male (Plug) |
|
|
|
02 |
= |
Female (Socket) |
|
WW |
= |
Connector Grounding Feature |
||
|
|
|
12 |
= |
No Grounding Detents |
|
|
|
24 |
= |
Grounding Detents |
|
X |
= |
Connector Shell Protective Coating |
||
|
|
|
5 |
= |
Sulfamate Nickel Plating |
|
|
|
6 |
= |
Zinc Plating – Yellow Chromate Coating |
|
Y |
= |
Contact Gold Plating over 50-microinches
(1.27 µm) Nickel |
||
|
|
|
1 |
= |
Gold ~ 50-microinches (1.27 µm) |
|
|
|
2 |
= |
Gold ~ 30-microinches (0.762 µm) |
|
|
|
3 |
= |
Gold Flash ~ <10-microinches
(<0.254 µm) |
Elite Electronics requires its fabricating sources to provide a written ISO Certificate of Compliance (C of C) inclusive of the product's ISO Manufacturing Date Code, RoHS - 2002/95/EC (Directive on the Restriction of the use of Certain Hazardous Substances in Electrical & Electronic Equipment) and WEEE - 2002/96/EC (Directive on Waste Electrical & Electronic Equipment) compliance with each production shipment.
This Web Site is best viewed using Internet Explorer 7.0 or Mozilla Firefox. Send mail to webmaster@elitelex.com with questions or comments about this web site. Copyright 1995 - 2011 Elite Electronics, Incorporated
